? semiconductor components industries, llc, 2016 july, 2016 ? rev. 11 1 publication order number: mc10el33/d mc10el33, mc100el33 5 v ecl 4 divider description the mc10el/100el33 is an integrated 4 divider. the differential clock inputs and the v bb allow a differential, single-ended or ac coupled interface to the device. the v bb pin, an internally generated voltage supply, is available to this device only. for single-ended input conditions, the unused differential input is connected to v bb as a switching reference voltage. v bb may also rebias ac coupled inputs. when used, decouple v bb and v cc via a 0.01 f capacitor and limit current sourcing or sinking to 0.5 ma. when not used, v bb should be left open. the reset pin is asynchronous and is asserted on the rising edge. upon power-up, the internal flip-flops will attain a random state; the reset allows for the synchronization of multiple el33?s in a system. the 100 series contains temperature compensation. features ? 650 ps propagation delay ? 4.0 ghz toggle frequency ? esd protection: ? > 1 kv human body model ? > 100 v machine model ? pecl mode operating range: v cc = 4.2 v to 5.7 v with v ee = 0 v ? necl mode operating range: v cc = 0 v with v ee = ? 4.2 v to ? 5.7 v ? internal input pulldown resistors on clk(s) and r. ? meets or exceeds jedec spec eia/jesd78 ic latchup test ? moisture sensitivity: ? level 1 for soic ? 8 nb ? level 3 for tssop ? 8 ? for additional information, see application note and8003/d ? flammability rating: ul 94 v ? 0 @ 0.125 in, oxygen index: 28 to 34 ? transistor count = 95 devices ? these devices are pb-free, halogen free and are rohs compliant figure 1. logic diagram and pinout assignment 4 3 1 2 5 6 7 8 q v ee v cc q clk v bb r 4 reset clk *for additional marking information, refer to application note and8002/d . marking diagrams* kl33 alyw soic ? 8 nb d suffix case 751 ? 05 1 8 tssop ? 8 dt suffix case 948r ? 02 1 8 1 8 ordering information www.onsemi.com kel33 alyw 1 8 hl33 alyw 1 8 hel33 alyw 1 8 (note: microdot may be in either location) h = mc10 k = mc100 a = assembly location l = wafer lot y = year w = work week = pb-free package soic ? 8 nb tssop ? 8 see detailed ordering and shipping information on page 6 of this data sheet.
mc10el33, mc100el33 www.onsemi.com 2 table 1. pin description pin function clk, clk reset q, q v bb v cc v ee ecl clock inputs* ecl asynch reset* ecl data outputs reference voltage output positive supply negative supply *pins will default low when left open. table 2. maximum ratings symbol parameter condition 1 condition 2 rating unit v cc pecl mode power supply v ee = 0 v 8 v v ee necl mode power supply v cc = 0 v ? 8 v v i pecl mode input voltage necl mode input voltage v ee = 0 v v cc = 0 v v i v cc v i v ee 6 ? 6 v i out output current continuous surge 50 100 ma i bb v bb sink/source 0.5 ma t a operating temperature range ? 40 to +85 c t stg storage temperature range ? 65 to +150 c ja thermal resistance (junction-to-ambient) 0 lfpm 500 lfpm soic ? 8 nb soic ? 8 nb 190 130 c/w jc thermal resistance (junction-to-case) standard board soic ? 8 nb 41 to 44 c/w ja thermal resistance (junction-to-ambient) 0 lfpm 500 lfpm tssop ? 8 tssop ? 8 185 140 c/w jc thermal resistance (junction-to-case) standard board tssop ? 8 41 to 44 5% c/w t sol wave solder (pb-free) < 2 to 3 sec @ 260 c 265 c stresses exceeding those listed in the maximum ratings table may damage the device. if any of these limits are exceeded, device function ality should not be assumed, damage may occur and reliability may be affected.
mc10el33, mc100el33 www.onsemi.com 3 table 3. 10el series pecl dc characteristics (v cc = 5.0 v; v ee = 0.0 v (note 1)) ? 40 c 25 c 85 c symbol characteristic min typ max min typ max min typ max unit i ee power supply current 27 33 27 33 27 33 ma v oh output high voltage (note 2) 3920 4010 4110 4020 4105 4190 4090 4185 4280 mv v ol output low voltage (note 2) 3050 3200 3350 3050 3210 3370 3050 3227 3405 mv v ih input high voltage (single-ended) 3770 4110 3870 4190 3940 4280 mv v il input low voltage (single-ended) 3050 3500 3050 3520 3050 3555 mv v bb output voltage reference 3.57 3.7 3.65 3.75 3.69 3.81 v v ihcmr input high voltage common mode range (differential configuration) (note 3) 2.5 4.6 2.5 4.6 2.5 4.6 v i ih input high current 150 150 150 a i il input low current 0.5 0.5 0.3 a note: device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printe d circuit board with maintained transverse airflow greater than 500 lfpm. electrical parameters are guaranteed only over the declared operating temperature range. functional operation of the device exceeding these conditions is not implied. device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. input and output parameters vary 1:1 with v cc . v ee can vary +0.25 v / ? 0.5 v. 2. outputs are terminated through a 50 resistor to v cc ? 2.0 v. 3. v ihcmr min varies 1:1 with v ee , v ihcmr max varies 1:1 with v cc . the v ihcmr range is referenced to the most positive side of the differential input signal. normal operation is obtained if the high level falls wi thin the specified range and the peak-to-peak voltage lies betwe en v pp min and 1 v. table 4. 10el series necl dc characteristics (v cc = 0.0 v; v ee = ? 5.0 v (note 1)) ? 40 c 25 c 85 c symbol characteristic min typ max min typ max min typ max unit i ee power supply current 27 33 27 33 27 33 ma v oh output high voltage (note 2) ? 1080 ? 990 ? 890 ? 980 ? 895 ? 810 ? 910 ? 815 ? 720 mv v ol output low voltage (note 2) ? 1950 ? 1800 ? 1650 ? 1950 ? 1790 ? 1630 ? 1950 ? 1773 ? 1595 mv v ih input high voltage (single-ended) ? 1230 ? 890 ? 1130 ? 810 ? 1060 ? 720 mv v il input low voltage (single-ended) ? 1950 ? 1500 ? 1950 ? 1480 ? 1950 ? 1445 mv v bb output voltage reference ? 1.43 ? 1.30 ? 1.35 ? 1.25 ? 1.31 ? 1.19 v v ihcmr input high voltage common mode range (differential configuration) (note 3) ? 2.5 ? 0.4 ? 2.5 ? 0.4 ? 2.5 ? 0.4 v i ih input high current 150 150 150 a i il input low current 0.5 0.5 0.3 a note: device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printe d circuit board with maintained transverse airflow greater than 500 lfpm. electrical parameters are guaranteed only over the declared operating temperature range. functional operation of the device exceeding these conditions is not implied. device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. input and output parameters vary 1:1 with v cc . v ee can vary +0.25 v / ? 0.5 v. 2. outputs are terminated through a 50 resistor to v cc ? 2.0 v. 3. v ihcmr min varies 1:1 with v ee , v ihcmr max varies 1:1 with v cc . the v ihcmr range is referenced to the most positive side of the differential input signal. normal operation is obtained if the high level falls wi thin the specified range and the peak-to-peak voltage lies betwe en v pp min and 1 v.
mc10el33, mc100el33 www.onsemi.com 4 table 5. 100el series pecl dc characteristics (v cc = 5.0 v; v ee = 0.0 v (note 1)) ? 40 c 25 c 85 c symbol characteristic min typ max min typ max min typ max unit i ee power supply current 27 33 27 33 31 37 ma v oh output high voltage (note 2) 3915 3995 4120 3975 4045 4120 3975 4050 4120 mv v ol output low voltage (note 2) 3170 3305 3445 3190 3295 3380 3190 3295 3380 mv v ih input high voltage (single-ended) 3835 4120 3835 4120 3835 4120 mv v il input low voltage (single-ended) 3190 3525 3190 3525 3190 3525 mv v bb output voltage reference 3.62 3.74 3.62 3.74 3.62 3.74 v v ihcmr input high voltage common mode range (differential configuration) (note 3) 2.5 4.6 2.5 4.6 2.5 4.6 v i ih input high current 150 150 150 a i il input low current 0.5 0.5 0.5 a note: device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printe d circuit board with maintained transverse airflow greater than 500 lfpm. electrical parameters are guaranteed only over the declared operating temperature range. functional operation of the device exceeding these conditions is not implied. device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. input and output parameters vary 1:1 with v cc . v ee can vary +0.8 v / ? 0.5 v. 2. outputs are terminated through a 50 resistor to v cc ? 2.0 v. 3. v ihcmr min varies 1:1 with v ee , v ihcmr max varies 1:1 with v cc . the v ihcmr range is referenced to the most positive side of the differential input signal. normal operation is obtained if the high level falls wi thin the specified range and the peak-to-peak voltage lies betwe en v pp min and 1 v. table 6. 100el series necl dc characteristics (v cc = 0.0 v; v ee = ? 5.0 v (note 1)) ? 40 c 25 c 85 c symbol characteristic min typ max min typ max min typ max unit i ee power supply current 27 33 27 33 31 37 ma v oh output high voltage (note 2) ? 1085 ? 1005 ? 880 ? 1025 ? 955 ? 880 ? 1025 ? 955 ? 880 mv v ol output low voltage (note 2) ? 1830 ? 1695 ? 1555 ? 1810 ? 1705 ? 1620 ? 1810 ? 1705 ? 1620 mv v ih input high voltage (single-ended) ? 1165 ? 880 ? 1165 ? 880 ? 1165 ? 880 mv v il input low voltage (single-ended) ? 1810 ? 1475 ? 1810 ? 1475 ? 1810 ? 1475 mv v bb output voltage reference ? 1.38 ? 1.26 ? 1.38 ? 1.26 ? 1.38 ? 1.26 v v ihcmr input high voltage common mode range (differential configuration) (note 3) ? 2.5 ? 0.4 ? 2.5 ? 0.4 ? 2.5 ? 0.4 v i ih input high current 150 150 150 a note: device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printe d circuit board with maintained transverse airflow greater than 500 lfpm. electrical parameters are guaranteed only over the declared operating temperature range. functional operation of the device exceeding these conditions is not implied. device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. input and output parameters vary 1:1 with v cc . v ee can vary +0.8 v / ? 0.5 v. 2. outputs are terminated through a 50 resistor to v cc ? 2.0 v. 3. v ihcmr min varies 1:1 with v ee , v ihcmr max varies 1:1 with v cc . the v ihcmr range is referenced to the most positive side of the differential input signal. normal operation is obtained if the high level falls wi thin the specified range and the peak-to-peak voltage lies betwe en v pp min and 1 v.
mc10el33, mc100el33 www.onsemi.com 5 table 7. ac characteristics (v cc = 5.0 v; v ee = 0.0 v or v cc = 0.0 v; v ee = ? 5.0 v (note 1)) ? 40 c 25 c 85 c symbol characteristic min typ max min typ max min typ max unit fmax maximum toggle frequency 3.4 4.2 3.8 4.2 3.8 4.2 ghz t plh t phl propagation delay clk to q reset to q 560 400 670 540 860 700 610 460 700 550 810 660 640 570 740 480 840 670 ps t rr set/reset recovery 400 200 400 200 400 200 ps v pp input swing (note 2) 150 1000 150 1000 150 1000 mv t jitter cycle-to-cycle jitter 1.0 1.0 1.0 ps t r t f output rise/fall times q (20% ? 80%) 100 225 350 100 225 350 100 225 350 ps note: device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printe d circuit board with maintained transverse airflow greater than 500 lfpm. electrical parameters are guaranteed only over the declared operating temperature range. functional operation of the device exceeding these conditions is not implied. device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. 10 series: v ee can vary +0.25 v / ? 0.5 v. 100 series: v ee can vary +0.8 v / ? 0.5 v. 2. v pp (min) is minimum input swing for which ac parameters guaranteed. the device has a dc gain of 40. figure 2. timing diagram clk reset q t rr figure 3. typical termination for output driver and device evaluation (see application note and8020/d ? termination of ecl logic devices) driver device receiver device qd q d z o = 50 z o = 50 50 50 v tt v tt = v cc ? 2.0 v
mc10el33, mc100el33 www.onsemi.com 6 ordering information device package shipping ? mc10el33dg soic ? 8 (pb-free) 98 units / rail MC10EL33DR2G soic ? 8 (pb-free) 2500 / tape & reel mc10el33dtg tssop ? 8 (pb-free) 100 units / rail mc100el33dg soic ? 8 (pb-free) 98 units / rail mc100el33dr2g soic ? 8 (pb-free) 2500 / tape & reel mc100el33dtg tssop ? 8 (pb-free) 100 units / rail ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d . resource reference of application notes an1405/d ? ecl clock distribution techniques an1406/d ? designing with pecl (ecl at +5.0 v) an1503/d ? eclinps i/o spice modeling kit an1504/d ? metastability and the eclinps family an1568/d ? interfacing between lvds and ecl an1672/d ? the ecl translator guide and8001/d ? odd number counters design and8002/d ? marking and date codes and8020/d ? termination of ecl logic devices and8066/d ? interfacing with eclinps and8090/d ? ac characteristics of ecl devices
mc10el33, mc100el33 www.onsemi.com 7 package dimensions soic ? 8 nb d suffix case 751 ? 07 issue ak seating plane 1 4 5 8 n j x 45 k notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimension a and b do not include mold protrusion. 4. maximum mold protrusion 0.15 (0.006) per side. 5. dimension d does not include dambar protrusion. allowable dambar protrusion shall be 0.127 (0.005) total in excess of the d dimension at maximum material condition. 6. 751 ? 01 thru 751 ? 06 are obsolete. new standard is 751 ? 07. a b s d h c 0.10 (0.004) dim a min max min max inches 4.80 5.00 0.189 0.197 millimeters b 3.80 4.00 0.150 0.157 c 1.35 1.75 0.053 0.069 d 0.33 0.51 0.013 0.020 g 1.27 bsc 0.050 bsc h 0.10 0.25 0.004 0.010 j 0.19 0.25 0.007 0.010 k 0.40 1.27 0.016 0.050 m 0 8 0 8 n 0.25 0.50 0.010 0.020 s 5.80 6.20 0.228 0.244 ? x ? ? y ? g m y m 0.25 (0.010) ? z ? y m 0.25 (0.010) z s x s m 1.52 0.060 7.0 0.275 0.6 0.024 1.270 0.050 4.0 0.155 mm inches scale 6:1 *for additional information on our pb-free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. soldering footprint*
mc10el33, mc100el33 www.onsemi.com 8 package dimensions dim min max min max inches millimeters a 2.90 3.10 0.114 0.122 b 2.90 3.10 0.114 0.122 c 0.80 1.10 0.031 0.043 d 0.05 0.15 0.002 0.006 f 0.40 0.70 0.016 0.028 g 0.65 bsc 0.026 bsc l 4.90 bsc 0.193 bsc m 0 6 0 6 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimension a does not include mold flash. protrusions or gate burrs. mold flash or gate burrs shall not exceed 0.15 (0.006) per side. 4. dimension b does not include interlead flash or protrusion. interlead flash or protrusion shall not exceed 0.25 (0.010) per side. 5. terminal numbers are shown for reference only. 6. dimension a and b are to be determined at datum plane -w-. seating plane pin 1 1 4 85 detail e b c d a g detail e f m l 2x l/2 ? u ? s u 0.15 (0.006) t s u 0.15 (0.006) t s u m 0.10 (0.004) v s t 0.10 (0.004) ? t ? ? v ? ? w ? 0.25 (0.010) 8x ref k ident k 0.25 0.40 0.010 0.016 tssop ? 8 dt suffix case 948r ? 02 issue a on semiconductor and are trademarks of semiconductor components industries, llc dba on semiconductor or its subsidiaries i n the united states and/or other countries. on semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property . a listing of on semiconductor?s product/patent coverage may be accessed at www.onsemi.com/site/pdf/patent ? marking.pdf . on semiconductor reserves the right to make changes without further notice to any products herein. on semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does o n semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. buyer is responsible for its products and applications using on semiconductor products, including compliance with all laws, reg ulations and safety requirements or standards, regardless of any support or applications information provided by on semiconductor. ?typical? parameters which may be provided in on semiconductor data sheets and/or specifications can and do vary in dif ferent applications and actual performance may vary over time. all operating parameters, including ?typic als? must be validated for each customer application by customer?s technical experts. on semiconductor does not convey any license under its patent rights nor the right s of others. on semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any fda class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. should buyer purchase or use on semicondu ctor products for any such unintended or unauthorized application, buyer shall indemnify and hold on semiconductor and its officers, employees, subsidiaries, affiliates, and distrib utors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that on semiconductor was negligent regarding the design or manufacture of the part. on semiconductor is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5817 ? 1050 mc10el33/d literature fulfillment : literature distribution center for on semiconductor 19521 e. 32nd pkwy, aurora, colorado 80011 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative eclinps is a trademark of semiconductor components industries, llc (scillc) or its subsidiaries in the united states and/or oth er countries.
|
